How To Install Brita Filter

Download Commodity

Download Article

Brita h2o filtration uses carbon to filter impurities out of your tap water. You can choose several models, including a bullpen, a faucet zipper or a sink dispenser model. You should choose your model according to whether y'all want to simply filter drinking water or if you lot want to filter all the water that goes through your sink.

i
Read the instructions on the Brita water filter cartridge packaging. The installation method has changed within the final few years. If you have older models, y'all volition need to presoak your filter in for 15 minutes in a glass of water.
- For all recently purchased filters, follow the remaining instructions.
ii

Remove the old filter and discard it. Wash your Brita bullpen with lather and water if yous haven't washed and then in the final few weeks.^[ane]

Advertisement
three

Wash your hands with lather and h2o. Unwrap your Brita pitcher filter.
4

Plow on the tap. Allow cold water run over your filter for xv seconds.^[two]
5

Insert the new filter. Run water over the summit of the carafe and filter. Echo every xl gallons (151.four L) or 2 months.^[3]

Advertisement

ane

Buy a Brita faucet filtration system. Your filtration system should come with two adaptors to fit most kitchen sinks. It is an exterior filter that tin be easily removed and replaced when the filter is no longer effective.
two

Unscrew the comprehend on the tap. The Brita filter will demand to screw onto the exterior threads on the tap. If your sink tap has interior threads, spiral on one of the adaptors earlier y'all install the organization.
three

Unwrap the base unit. Marshal the collar with the faucet threads. Turn the attachment carefully to connect the filter organisation to the faucet.^[4]
iv

Ensure the faucet is secure past turning it tightly with your easily. Test for leaks by turning on the cold water.
v

Go along the cold water on. Flush the arrangement for five minutes. It volition actuate the filter and remove carbon grit.^[5]
6

Apply for 100 gallons (378.5 L) earlier replacing. The green lite will indicate the filter is still good. The red light indicates you should change the system.^[6]

Advertisement

1

Unpack your three-manner filter tap and dispenser. This is the longest installation process, because you are actually replacing your sink tap with a Brita brand tap and hoses.
2

Remove the timer and testing strip. Run your tap water and insert the testing strip Consult the instructions to run across under what filtration setting yous should set the filter co-ordinate to your results.^[7]
3

Mount the filter timer to the inside of your sink cabinet, where it volition non get wet.
4

Plow off your water taps. Place a bucket underneath the pipes. Unscrew the pipes with a wrench so that y'all can remove your electric current kitchen sink faucet.
5

Remove all the pieces for the Brita tap and lay it nearby. Go on the directions close at hand in case yous need to identify parts.
6

Sideslip the shank over the three hoses. The shank is a collar-like metal piece.
7
Attach the hoses to the inside of the tap. Spiral the blue hoses into the hole marked "C." Screw the red hose into the hole marked "H."
- Screw the concluding hose into the hole marked "B." Make sure they are secure.
eight

Pull the shank toward the tap. Screw it into the lesser of the tap.
9

Identify your base on the hole in the kitchen counter, where your old tap was installed.
10

Mount the tap to the base. Pull the hoses and shank through the hole.
11

Fix your counter plate, gasket, locking ring and hexagon nut parts underneath the sink so that y'all tin can install them hands. Loop them through the hoses in that order.
12

Screw the hexagonal nut into place on the shank. Suit the dispenser at the height, and then that it is positioned correctly. Set up the dispenser in place at the bottom using a wrench.
13

Connect your hoses. The red hose will connect with the hot water supply. Next, insert the gasket into the T-piece, which you lot will place over the cold water intake.
xiv

Screw the T-piece onto the top of the cold water supply. Insert the gaskets into the remaining hoses. Connect each side to the Brita filter device.^[8]
15

Insert the filter cartridge into the blue Brita filter device. The system is fix. Install the wall mount to hold your filter device in place so that it can exist unscrewed and replaced when it is no longer constructive.
16

Turn on the common cold water tap. Run the faucet. Check for leaks.
17
Pay attention to your filter timer so that you know when it's fourth dimension to alter. Unlock the electric current filter, release the pressure handle and pull the filter out. Replace it with a new filter and secure the locking handle.
- Reset your timer. Recycle your Brita cartridge.^[9]
Advertisement

Add together New Question

Question

When I turn my sink on, water comes out from the filtered cervix as well. How can I fix this?

In that location is a well known defect with a sure model that Brita has been repairing, which sounds like the issue you're having. Call Brita and meet if they tin can send out a repairman to ready the internal plastic pipe that has broken.